阿里云运行 Calico¶
本文将介绍如何在阿里云自建集群上，安装使用 Calico 作为集群 CNI。
安装集群¶
在阿里云上准备好一套自建 Kubernetes 集群，或按照搭建 Kubernetes 集群文档手动搭建一套集群。 集群安装完成之后，下载 Calico 的部署清单文件:
推荐使用以下命令加速镜像拉取:
sed -i 's?docker.io?docker.m.daocloud.io?g' calico.yaml
下面分别演示使用隧道模式和路由模式:
隧道模式(IPIP)¶
Vxlan 和 IPIP 协议不依赖底层网络，通过封装构建一个大二层覆盖网络以实现网络连通，所以能够运行在大多数公有云上， 此模式不依赖 CCM。 Calico 部署清单文件默认使用 IPIP 模式，使用以下命令安装:
等待安装完成:
# kubectl get po -n kube-system | grep calico
calico-kube-controllers-769669454f-c9pw6 1/1 Running 0 1m
calico-node-679wb 1/1 Running 0 1m
calico-node-6wzkj 1/1 Running 0 1m
创建测试 deployment，验证连通性:
$ kubectl get po -o wide
NAME READY STATUS RESTARTS AGE IP NODE NOMINATED NODE READINESS GATES
test-77877f4755-24gqt 1/1 Running 0 13m 10.244.236.193 cn-chengdu.i-2vcxxr <none> <none>
test-77877f4755-2d6r8 1/1 Running 0 13m 10.244.140.2 cn-chengdu.i-2vcxxs <none> <none>
$ kubectl get svc
NAME TYPE CLUSTER-IP EXTERNAL-IP PORT(S) AGE
kubernetes ClusterIP 172.21.0.1 <none> 443/TCP 31d
test ClusterIP 172.21.0.83 <none> 80/TCP 2m
# 跨节点访问 Pod
$ kubectl exec test-77877f4755-24gqt -- ping -c1 10.244.140.2
PING 10.244.140.2 (10.244.140.2) 56(84) bytes of data.
64 bytes from 10.244.140.2: icmp_seq=1 ttl=62 time=0.471 ms
--- 10.244.140.2 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.471/0.471/0.471/0.000 ms
# 访问外部
$ kubectl exec test-77877f4755-24gqt -- ping -c1 8.8.8.8
PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data.
64 bytes from 8.8.8.8: icmp_seq=1 ttl=109 time=38.5 ms
--- 8.8.8.8 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 38.479/38.479/38.479/0.000 ms
# 访问 ClusterIP
$ kubectl exec test-77877f4755-24gqt -- curl -i 172.21.0.83
% Total % Received % Xferd Average Speed Time Time Time Current
Dload Upload Total Spent Left Speed
100 153 100 153 0 0 93463 0 --:--:-- --:--:-- --:--:-- 149k
HTTP/1.1 200 OK
Content-Type: application/json
Date: Wed, 27 Sep 2023 08:15:34 GMT
Content-Length: 153
经过测试: IPIP 和 Vxlan 模式下各种通信正常，并且不依赖 CCM发布路由以实现 Pod 间的通信, 但 LoadBalancer Service 的实现依赖 CCM
非隧道模式¶
当 Calico 运行在非隧道模式，Pod 之间通信直接对接底层网络，所以常常需要一些其他设备发布路由，以使 Pod 子网路由集群外可达。在非公有云上需要支持运行 BGP 协议的路由器，在公有云上需要支持一些往外的组件发布 Pod 子网路由到 VPC 网络，如阿里云的 CCM。 但 CCM组件发布路由常常以节点为单位，这就要求不同节点的 Pod 属于不同的段，同一节点的 Pod 属于同一个段。而 Calico 自有的 IPAM: calico-ipam 无法满足这一点(calico-ipam 以 block 为单位, 而不是以节点为单位)。所以针对这种情况，我们可以通过切换 ipam 为 host-local 或 spiderpool 来解决。
节点的 PodCIDR 对应 Node.spec.podCIDR 字段
- host-local: 非常简单的 IPAM，从节点的 PodCIDR 中分配 IP, 分配的数据存放于本地磁盘, 无其他 IPAM 能力
- Spiderpool: 提供非常强大的 IPAM 能力，支持按节点分配 IP、支持固定 IP、多网卡分配 IP 等高级特性
在介绍如何使用之前，需要先安装 CCM 组件， 参考安装 CCM 文档，并且切换 Calico 为非隧道模式，修改 calico-node daemonSet 部署清单文件中以下几个环境变量为 Never:
# Enable IPIP
- name: CALICO_IPV4POOL_IPIP
value: "Never"
# Enable or Disable VXLAN on the default IP pool.
- name: CALICO_IPV4POOL_VXLAN
value: "Never"
# Enable or Disable VXLAN on the default IPv6 IP pool.
- name: CALICO_IPV6POOL_VXLAN
value: "Never"
# Set MTU for tunnel device used if ipip is enabled
Host-local 作为 IPAM¶
首先切换 IPAM 为 host-local，这需要修改 Calico 安装清单文件中 ConfigMap, 如下:
# Source: calico/templates/calico-config.yaml
# This ConfigMap is used to configure a self-hosted Calico installation.
kind: ConfigMap
apiVersion: v1
metadata:
name: calico-config
namespace: kube-system
data:
# Typha is disabled.
typha_service_name: "none"
# Configure the backend to use.
calico_backend: "bird"
# Configure the MTU to use for workload interfaces and tunnels.
# By default, MTU is auto-detected, and explicitly setting this field should not be required.
# You can override auto-detection by providing a non-zero value.
veth_mtu: "0"
# The CNI network configuration to install on each node. The special
# values in this config will be automatically populated.
cni_network_config: |-
{
"name": "k8s-pod-network",
"cniVersion": "0.3.1",
"plugins": [
{
"type": "calico",
"log_level": "info",
"log_file_path": "/var/log/calico/cni/cni.log",
"datastore_type": "kubernetes",
"nodename": "__KUBERNETES_NODE_NAME__",
"mtu": __CNI_MTU__ ,
"ipam": {
"type": "host-local",
"ranges": [[{ "subnet": "usePodCidr" }]]
},
"policy": {
"type": "k8s"
},
"kubernetes": {
"kubeconfig": "__KUBECONFIG_FILEPATH__"
}
},
{
"type": "portmap",
"snat": true,
"capabilities": {"portMappings": true}
},
{
"type": "bandwidth",
"capabilities": {"bandwidth": true}
}
]
}
---
IPAM 部分切换为 host-local, 并且指定使用节点的 PodCIDR 作为 Pod 的子网
安装并等待 Calico 就绪之后，创建测试应用可以发现 Pod 的 IP 属于节点的 PodCIDR(10.244.0.0/24 和 10.244.1.0/24):
$ k get po -o wide
NAME READY STATUS RESTARTS AGE IP NODE NOMINATED NODE READINESS GATES
test-77877f4755-58hlc 1/1 Running 0 5s 10.244.0.2 cn-chengdu.i-2vcxxr <none> <none>
test-77877f4755-npcgs 1/1 Running 0 5s 10.244.1.2 cn-chengdu.i-2vcxxs <none> <none>
经过测试，Pod 的各种通信正常。
Spiderpool 作为 IPAM¶
-
首先切换 IPAM 为
spiderpool，这需要修改 Calico 安装清单文件中 ConfigMap, 如下:# Source: calico/templates/calico-config.yaml # This ConfigMap is used to configure a self-hosted Calico installation. kind: ConfigMap apiVersion: v1 metadata: name: calico-config namespace: kube-system data: # Typha is disabled. typha_service_name: "none" # Configure the backend to use. calico_backend: "bird" # Configure the MTU to use for workload interfaces and tunnels. # By default, MTU is auto-detected, and explicitly setting this field should not be required. # You can override auto-detection by providing a non-zero value. veth_mtu: "0" # The CNI network configuration to install on each node. The special # values in this config will be automatically populated. cni_network_config: |- { "name": "k8s-pod-network", "cniVersion": "0.3.1", "plugins": [ { "type": "calico", "log_level": "info", "log_file_path": "/var/log/calico/cni/cni.log", "datastore_type": "kubernetes", "nodename": "__KUBERNETES_NODE_NAME__", "mtu": __CNI_MTU__ , "ipam": { "type": "spiderpool" }, "policy": { "type": "k8s" }, "kubernetes": { "kubeconfig": "__KUBECONFIG_FILEPATH__" } }, { "type": "portmap", "snat": true, "capabilities": {"portMappings": true} }, { "type": "bandwidth", "capabilities": {"bandwidth": true} } ] }切换 IPAM 为 Spiderpool 并等待就绪。
-
安装 Spiderpool
helm repo add spiderpool https://spidernet-io.github.io/spiderpool helm repo update spiderpool helm install spiderpool spiderpool/spiderpool --namespace kube-system --wait需要提前安装 Helm 二进制 Spiderpool 默认会安装 Multus 组件，如果你不需要 Multus 或已经安装 Multus，可以使用
--set multus.multusCNI.install=false"关闭安装 Multus。安装完成之后，需要为每个节点的 podCIDR 创建一个对应的 Spiderpool IP 池供 Pod 使用:
$ kubectl get nodes -o=custom-columns='NAME:.metadata.name,podCIDR:.spec.podCIDR' NAME podCIDR cn-chengdu.i-2vcxxr 10.244.0.0/24 cn-chengdu.i-2vcxxs 10.244.1.0/24创建以下 Spiderpool IP 池:
apiVersion: spiderpool.spidernet.io/v2beta1 kind: SpiderIPPool metadata: name: cn-chengdu.i-2vcxxr spec: default: true ips: - 10.244.0.1-10.244.0.253 subnet: 10.244.0.0/16 nodeName: - cn-chengdu.i-2vcxxr --- apiVersion: spiderpool.spidernet.io/v2beta1 kind: SpiderIPPool metadata: name: cn-chengdu.i-2vcxxs spec: default: true ips: - 10.244.1.1-10.244.1.253 subnet: 10.244.0.0/16 nodeName: - cn-chengdu.i-2vcxxs注意 ips 中属于对应 nodeName 节点的 podCIDR
-
创建测试应用，并测试连通性
$ kubectl get po -o wide NAME READY STATUS RESTARTS AGE IP NODE NOMINATED NODE READINESS GATES test-77877f4755-nhm4f 1/1 Running 0 27s 10.244.0.179 cn-chengdu.i-2vcxxr <none> <none> test-77877f4755-sgqbx 1/1 Running 0 27s 10.244.1.193 cn-chengdu.i-2vcxxs <none> <none> $ kubectl get svc NAME TYPE CLUSTER-IP EXTERNAL-IP PORT(S) AGE kubernetes ClusterIP 172.21.0.1 <none> 443/TCP 31d test ClusterIP 172.21.0.166 <none> 80/TCP 3m43s$ kubectl exec test-77877f4755-nhm4f -- ping -c1 10.244.1.193 PING 10.244.1.193 (10.244.1.193) 56(84) bytes of data. 64 bytes from 10.244.1.193: icmp_seq=1 ttl=62 time=0.434 ms --- 10.244.1.193 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.434/0.434/0.434/0.000 ms测试访问 ClusterIP:
$ kubectl exec test-77877f4755-nhm4f -- curl -i 172.21.0.166 % Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed 100 153 100 153 0 0 127k 0 --:--:-- --:--:-- --:--:-- 149k HTTP/1.1 200 OK Content-Type: application/json Date: Wed, 27 Sep 2023 10:27:48 GMT Content-Length: 153经过测试，Pod 各种连通性正常。另外 Calico 创建的 Pod 也可以使用 Spiderpool 的其他高级 IPAM 能力。